| |
|
|
|
VM1000
|
Price
Blog |
|
Feature
|
|
|
1. |
7.5HP high torque spindle motor,low noise and vibration |
|
2. |
BT40/CAT40/DIN40 6000 rpm spindle speed, (Optional 8,000, 10,00, 12,000 or
15,000rpm ) with P4 angular contact spindle bearings. |
|
3. |
10 Tools Armless ATC, Full enclosure guarding |
|
4. |
32mm,C5 precision ground ballscrews to minimize backlash, provides high
precision movement and reduces heat deformation on all axes. |
|
5. |
Fully Counterbalanced Z Axis Slide with Zaxis brake Motor to Eliminate Spindle
and part Damage on Power Failure. |
|
6. |
Precision linear guide ways are installed on each axis to provide high speed and
high accuracy performance. |
|
7. |
Meehanite Casting with annealed & stress relieved |
|
8. |
Direct-driven transmission between motor and ballscrew by coupling provides zero
backlash. |
|
9. |
100% Laser tested for positioning accuracy & repeatability |
|
10. |
Ball Bar tested for circular interpolation accuracy |
|
11. |
Table and chip Guarding (Optional, instead of standard Full
Guarding) |
|
12. |
Tool box & Tools |
|
13. |
Positioning Accuracy: +0.0004”/ft |
|
14. |
Repeatability Accuracy: +0.0002/ft |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Specification
|
TABLE |
|
|
Table size |
12” x 61” (305 x 1524mm) |
|
T-Slot (Size x Qty x Distance) |
0.63” x 3 x 4” |
|
Longitudinal travel: |
40.2” (1020mm) |
|
Cross travel : |
16” (400mm) |
|
Vertical travel: |
16” (400mm) |
|
Table Load: |
670 lbs evenly distributed |
|
Spindle nose to table top: |
4”-20”(102-502mm) |
|
Column surface to center of table: |
9”-25” (229-635mm) |
|
SPINDLE |
|
|
Spindle taper: |
CT#40 |
|
Spindle Speed (r. p.m.): |
6000 rpm (8000-15,000 optional) |
|
Spindle center to column front surface: |
16.26” (413mm) |
|
Spindle motor: |
7.5HP AC SERVO SPINDLE MOTOR |
|
Max Torque: |
26 ft – lb @ 1500 rpm |
|
Drive on XYZ: |
1KW AC SERVO |
|
Max Thrust rating: |
2000 lb |
|
TOOL CHANGER: |
|
|
Capacity: |
10-station |
|
Max. Tool Diameter: |
Full:3.9” Next Empty:5.9” |
|
Max. Tool Length: |
4” semi-guarding |
|
Max. Tool Weight: |
13.4 lb |
|
Tool-to-Tool (avg.): |
5.7 Sec. |
|
FEED RATE: |
|
|
XYZ axes feed rates (per min.): |
393 inch/min |
|
Rapid traverse X,Y,Z axes(per min.): |
472 inch/min |
|
GENERAL: |
|
|
Coolant pump: |
1/6HP |
|
Lubrication pump: |
80W |
|
Air Source: |
6Kg/cm2 (70 psi) |
|
Power requirement: |
12 KVA |
|
Length X Width X Height (A X B X C): |
63.4”x78.7”x93.9” |
|
|
(1610mm x 2000mm x 2386mm) |
|
Net Weight: |
6147 lbs. (2700 Kgs) |
|
|
|
Standard Accessory
|
Control
System
|
|
|
Full enclosure guarding |
Mitsubishi E60 (Standard) |
|
Way Covers for Y and Z Axis |
Fagor 8055i FL |
|
Central automatic lubrication system |
Mitsubishi M70 |
|
Coolant System and air blast system
|
Fanuc Oi-mate |
|
Quartz work light |
Fanuc Oi-MC |
|
Tool Box with Tools |
|
|
Spindle Orientation |
|
|
End of Program and Alarm Light |
|
|
|
Optional Accessory
|
|
10-Station Automatic Tool Changer |
|
CT40 Arm type 24 tools ATC |
|
Screw-type Chip Auger with chip bucket |
|
Rigid Tapping |
|
CT40 belt type spindle speed 8000rpm,10000rpm,12000rpm |
|
Oil mist lubrication pump |
|
Spindle oil cooler 4000BTU |
|
Coolant through spindle center (30 Bar) |
|
Oil through tool holder |
|
External Transformer , 420-510-240V, 60HZ, 15 KVA |
|
MPG Hand wheel |
|
All Specifications And Designs
Are Subject To Change Without Notice. |
|
|
|
|
|
